ClearFlow ® (Dielectric Fitting)

19200P - 19203P

Grooved x Threaded

Description:

Clearflow® fittings protect your plumbing system through an exclusive steel-to-plastic design that establishes an effective dielectric waterway. The Clearflow® line of dielectric fittings separates dissimilar metals in the electrolyte (waterway) eliminating the local galvanic cell.

In addition, Clearflow‘s® metal-to-metal joint design maintains external electrical continuity, thereby preventing stray current corrosion. This feature becomes critical when stray current is present due to intentional or non-intentional grounding of direct current (DC) sources, e.g. phone systems and appliances.

Clearflow® fittings are designed to meet the requirements of ASTM standard F-1545 for continuous use at temperatures up to +225°F (- +5°F) and for pressures up to 300psi, and will achieve a dielectric waterway in all potable water and appropriate HVAC applications. Clearflow® is listed by IAPMO/UPC and SBCCI PST & ESI. Test results comparing Clearflow® fittings with several other connections are provided below

Features:
  • Allows for Metal to Metal electrical continuity
  • Protects your plumbing system
  • Several Install Options
INSTALLATION:

Test results:
A test was conducted by Pittsburgh testing Laboratory to determine a Clearflow® fitting’s ability to reduce the current flow that causes internal corrosion in a waterway system.

This current flow exists when dissimilar metals are exposed to an electrolyte (water) and is directly proportional to the rate at which corrosion occurs. The test fittings were installed between a piece of copper tubing and galvanized steel pipe. The current flow across these fittings was measured and recorded.

Fittings tested:
Sample #1 ¾”x3” ClearFlow® connector Part No. 19125
Sample #2 ¾”x 3” galvanized pipe nipple
Sample #3 ¾” insulated dielectric union
Sample #4 ¾” x 2” insulated coupling

Four test samples:
Sample #1 A 12” section of copper tubing was connected to a copper sweat ¾” NPT adapter, Plexiglas test insulator, galvanized coupling, a ¾”x 3” Clearflow® Connector, and a 12” section of galvanized steel pipe.
Sample #2 A 12” section of copper tubing was connected to a copper sweat ¾” NPT adapter, Plexiglas test insulator, galvanized coupling, a ¾”x 3” Clearflow® Connector, and a 12” section of galvanized steel pipe.
Sample #3 A 12” section of copper tubing was connected to a ¾” insulated dielectric union and a 12”section of galvanized pipe.
Sample #4 A 12” section of copper tubing was connected to a ¾”x 2”insulated coupling and a 12”section of galvanized pipe.

Test procedures:
After each test sample was assembled, a plastic cap was installed on the copper tubing. Each sample was filled with 70°F tap water. One lead of the multimeter was connected to the copper tubing. The other lead was connected to the galvanized pipe. A current reading was taken for each sample.

The results:
Sample #1 (Clearflow® Dielectric Waterway Connectors): 0.066 ma
Sample #2 (Galvanized Pipe Nipple): 0.345 ma
Sample #3 (Insulated Dielectric Union): 0.441 ma
Sample #4 (Insulated Coupling): 0.209 ma
NOTE: Certified results of these tests are available upon request.

Test data/results and listings:
The facts and test data reported herein have been certified by Pittsburgh Testing Laboratory and collected by Elster Perfection Corporation engineers in our own laboratories. Similar testing on Clearflow® type fittings have been certified by Heron Testing Labs, Inc. Also, the corrosion protection effects of Clearflow® type fittings has been proven in tens of millions of water heaters. We have been supplying these fittings world wide to water heater manufacturers for more than 20 years. Variations of Clearflow® fittings are used in appliances listed by the following agencies: The American Gas Association (A.G.A.) Laboratories; Underwriters Laboratories (U.L.); and

The Canadian Gas Association (C.G.A.).

The test equipment used was a Micronta digital multimeter, #22-191 that is sensitivity rated at 20,000 VDC.

 
PART NUMBERS & SPECIFICATIONS
 
PART NUMBER
Grooved x Threaded Parts and Measurements
       
       
 
Caption
Can't Find what you are looking for?
Please contact us at 503-328-6705 for TECHNICAL/SALES Support.